service hotline



Name: SD-60
Product catalog: DC DC Converter

Print this Page        Skype Online

E-mail Us                QQ

Whatsapp               wangwang

Facebook                Youtube

60W Single Output DC-DC Converter   SD-60 series
2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
Fixed switching frequency at 83 KHz
Low cost
High reliability
2 years warranty

Model SD-60A-5 SD-60B-5 SD-60C-5 SD-60A-12 SD-60B-12 SD-60C-12 SD-60A-24 SD-60B-24 SD-60C-24
DC Voltage 5V 12V 24V
Rated Current 12A 5A 2.5A
Current Range 0~12A 0~5A 0~2.5A
Rated Power 60W 60W 60W
Ripple & Noise 100mVp-p 120mVp-p 150mVp-p
Voltage Adj. Range 4.5~5.5VDC 11~16VDC 23~30VDC
Voltage Tolerance ±2.0% ±1.0% ±1.0%
Line Regulation ±0.5% ±0.3% ±0.2%
Load Regulation ±0.5% ±0.3% ±0.2%
Setup, Rise, Hold Up Time 2.5s,50ms,------at full load
Voltage Range A:9.2~18VDC   B:19~36VDC   C:36~72VDC
Efficiency  70% 73% 76% 72% 75% 78% 74% 80% 83%
DC Current 7A/12V 3A/24V 1.5A/48V
Over Load 105~150% rated output power
Protection type: Hiccup mode,recovers automatically after fault condition is removed
Over Voltage 5.75~6.75V/10%load 16.8~20V/10%load 31.5~37.5V/10%load
Protection type: Hiccup mode,recovers automatically after fault condition is removed
Working Temp. -10~+60℃ (Refer to "Derating Curve")
Working Humidity 20~90% RH non-condensing
Storage temp., Humidity -20~+85℃ ,10~95%RH
Temp. Coefficient ±0.03%/℃ (0~50℃)
Vibration 10~500Hz,2G10min./1cycle,60min.each along X, Y,Z axes
Safety Standards Design refer to LVD
Withstand Voltage I/P-O/P:1.5KVAC   I/P-FG:1.5KVAC   O/P-FG:0.5KVAC 
Isolation Resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC /25℃ /70%RH 
EMC Emission Compliance to EN55022(CISPR22)Class B
EMC Immunity Compliance to EN61000-4-2,3,4,6,8, EN55024, heavy industry level, criteria A
Dimension 159*97*38mm(L*W*H)
Weight 0.48Kg
Packing 24pcs/12.7Kg/0.75CUFT
1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.

If you have any enquiry about quotation or cooperation , please feel free to email us at or use the following enquiry form . Our sales representative will contact you within 24 hours. Thank you for your interest in our products.